product image
product image preview
product image preview
product image preview
product image preview
product image preview
product image preview

3 Pack Blink Mini No Drill No Screws Wall Mount Bracket for Blink Mini /Mini 2 /Outdoor 4 /Indoor Camera Mount Adhesive Bracket for Blink Camera

8.99

3 Pack Blink Mini No Drill No Screws Wall Mount Bracket for Blink Mini /Mini 2 /Outdoor 4 /Indoor Camera Mount Adhesive Bracket for Blink Camera

4.5

500+ bought in past month

Highest ranking 101

9 comments

$8.99

· 3 Pack white Blink Adhesive Wall Mount Bracket - Compatible with Blink Mini /Blink Mini 2 /Blink Outdoor 4 /Blink Indoor Cameras · No Drill No Screws Mount - Simply remove the adhesive tape film from the back of the mount, stick it in the desired location and let it sit for about 12 hours. Then slide the camera into the slot straight down to the bottom. · Using the Blink Camera Adhesive Wall Mount Bracket does not affect the angle adjustment of the blink camera. · Product design features: compatible with blink camera camera models, HBV adhesive area is large and super-strong adhesive, the bottom of the bracket with hooks for fixing the wire, so that the wire from breakage · What You Get:3 Pack white Wall Mount housing . Please feel free to contact us, any problem with received products or installation

Related products

Reviews From
avatar

Y. KangReviewed in the United States on April 18, 2025

I bought this to use with my Blink Mini 2. The back of the mount uses very strong adhesive. You can remove it by using a hairdryer for a minute to loosen it up. Also, very important note, for the Blink Mini 2 you need to pop the camera off the mount by pulling it straight up and then remove the outer plastic ring (see 2nd photo) and then snap the base on to the back of the camera instead of bottom of the camera (there are two attachment points, the camera will be mounted to the bottom of the camera by default) and mount the camera on to the holder. If you don’t remove the outer plastic ring before you mount the camera it will only be able to be tilted about 45-50 degrees down so you’ll basically only be monitoring straight ahead. Take the plastic ring off and you’ll be able to tilt the camera down much further, closer to 30 degrees which helps a lot if you mount the camera a bit higher. Also, even without that outer plastic ring the camera fits very snugly. Hope this helps!!

avatar

Tatyana PashnyakReviewed in the United States on April 7, 2025

Super easy to install and stay put!

avatar

RaminReviewed in the United States on March 28, 2025

I ordered couple times. Works great. No damage on wall. Fit for Blink.

avatar

JonesyReviewed in the United States on April 19, 2025

Works great. No problem stick to the painted drywall surface that I attached it to. Even has a cord organizer built in.

avatar

Shopaholic84Reviewed in the United States on October 10, 2024

Mine has been intact for a few months so, so far so good

avatar

TechmanrodReviewed in the United States on October 26, 2024

Although the original Blink mount is required for these, it gives you an option for mounting without drilling holes in your wall. I decided to buy them and test, and if they didn't work, would just drill holes at that point. I purchased a pack of 3 and installed 2 of them inside the house. I have had them up for 2 months so I think they are going to stay put without any issues. When using 3M type tape it is a guessing game whether they will hold or not. In this case, with a clean wall and the fact that the Blink cameras are light, it works well. I recommend these.

avatar

Kindle CustomerReviewed in the United States on January 31, 2025

Some work well, but i had a problem with a few of the sticky coming off. Would be nice if there was a hook so you could hang it by a thumb tac

avatar

Phillipp CunReviewed in the United States on May 7, 2025

I love this the glue is very strong. I hang it upside down inside and outside. Very worth getting.

avatar

ErikReviewed in Canada on August 8, 2024

Cole très bien