product image
product image preview
product image preview
product image preview
product image preview
product image preview
product image preview
product image preview

Creality Official CR-10 Platform Tempered Glass Bed with 4 Binder Clips, Removal Tool, 310x310x4mm, 3D Printer Cr-10s/Cr-10 V2 Upgraded Build Plate Printing Surface for Heated Bed

23.39

Save 10%

Creality Official CR-10 Platform Tempered Glass Bed with 4 Binder Clips, Removal Tool, 310x310x4mm, 3D Printer Cr-10s/Cr-10 V2 Upgraded Build Plate Printing Surface for Heated Bed

4.4

Highest ranking 101

7 comments

$23.39

Save 10%

· ➤Remove Easily: Once the hotbed cools back to room temperature, the carbon-silicone base will release the model which can be easily removed by hand. · ➤New Upgraded: Designed with small logo at the bottom of Tempered Glass to both avoid logo printing mark. · ➤Convenient to Use: The new glass plate can be placed on top of any existing hotbed surface and be held in place with simple clips. Clean with water or alcohol. Easy to remove your print by hand or with a scraper. · ➤No Edge Curling: As the hotbed heats to higher temperatures, it provides even more adhesion. Perfect for those ABS prints with difficult warping issues. · ➤Compatibility: Fit for CR-10, CR-10S, CR-10 S3, Sidewinder X1, Longer LK1, TENLOG TL-D3 Pro.

Related products

Reviews From
avatar

The Disgruntled TechReviewed in the United States on August 18, 2024

Just like everyone, my bed was warped. I've tried multiple different solutions but going back to a quality borosilicate glass with a textured surface is the best solution.

avatar

Waldon R.Reviewed in the United States on March 17, 2024

Fits perfectly, leveling bed much easier and great adhesion.

avatar

George MReviewed in Canada on March 18, 2025

I have a 2 year old CR10 Smart Pro. The original plate worked fine for quite a while, but it became warped. I needed to re-level every few prints. Not ideal. This plate is thick and flat. I leveled once and that was that. Prints were perfect. 55 degrees is all that is needed for adhesion. Note that the filament will leave a residue on the plate, but it does now affect performance. It can't be easily cleaned. I would not use Alcohol on this plate as you can with metal ones.

avatar

steedReviewed in Australia on June 14, 2024

Just need to add a little glue stick to the plate and it will stick perfectly

avatar

Moto'FreakReviewed in Canada on June 18, 2023

Without this for your CR-10 Smart Pro, you'll be always fighting bed leveling. And that all stopped when I removed the PEi sheet and installed this glass plate! Make sure to use PVP glue and have a metal scraper ( I use my Bambu Scraper ) to remove parts with ease! On the Cr-10 Smart Pro, you can use the clips that come with it, but you must use them with caution! the nozzle can hit them. You'll need to assign no go area on the bed or use different method to clamp the glass down. 100% print rate since switch to this glass plate!

avatar

Kindle CustomerReviewed in Australia on March 12, 2024

Does the job. Nice and flat. ( Not like Ali Express ones )

avatar

Andrew S.Reviewed in Canada on May 9, 2022

Well....I thought I'd try this. Maybe if you are doing larger parts it might be better, although can't see it. But so far the parts I am trying to print....do not stick. Removed the plastic, cleaned with alcohol and started printing. The filament will literally lift off the print bed. Then the nozzle will grab and pull it off more. I tried different temps from 190-215(PLA), I tried no part fan, and tried part fan after 2 layers. Wouldn't not even get to a 3rd layer to see. So yeah.....easily removable, because nothing sticks. I have better luck printing on straight glass with no hairspray or glue. It will come off and probably sit in a corner somewhere. Pretty expensive removal tool and 4 clips.