Just WOW!. I'll update with photos of my prints later on. I've been searching for matte filaments and there seems to be limited options. Not only have i think i found it, i dear say i found my goldilocks filament. Ordering 3 more rolls next week as I've been printing 24hrs a day since i got it a few days ago. Excited to try other colors. Roll was nicely wound and print quality is astounding, printing is very easily and was dialed very quickly. and i have zero complaints so far. Layer lines are pretty much invisible even at .2 layer heights. .13 is jaw dropping. Been printing an order for a local hobby shop and they at first didn't believe it was 3d printed as it looked multitudes better than previous filament I've used on their order. I've been printing on my mostly stock ender 3 v2. Only modifications are z-brace rods, bltouch, dual z and printed z motor mounts. Printing here the update NY winter is usually challenging as where i print in my home can be as low as 10c ( will be finishing my enclosure soon). Saying that my only struggle has been minor corner warping and bed adhesion. but i doubt that would be an issue in warmer rooms. The issue has been resolved though as i really squish my first layer (leaves very fine elephant foot that cleans quite easily with a sharp hobby knife or 220grit sand paper) since i print 7-20 parts at a time. Can't afford failures. I am printing on the stock textured side of the ender 3 glass bed. For those with an ender 3 i do Hot end at 195-200c, 60c bed temp at 40mm sec (as i prefer quality over speed ) retract 6.5mm 50mmsec, default cura coasting settings and filament equalizer enabled. 75%-100% fan after initial 2 layers. I'd also like to add that my printed upgrades are done in hatchbox abs for strength and temperature resistance. But now any parts that aren't at risk of high temperature exposure I'm using this matte black pla because it looks that amazing and is suitably strong. If I run into any issues I'll update accordingly. Update 7 Days Later So i ordered this filament for an order for a hobby shop. Printing drag racing slot car stands. I printed 96 of these in 4 different filaments. After the first 28 this filament arrived and after the first test prints i was amazed and now only use this filament. I went through the whole 1kg roll in 6 days. Ordered another and already been printing into the 2nd roll. I've updated my nozzle temp to 210c and I'm using a .8 brass nozzle. A worth while mention is these stands i print they're only 3 bottom 2 top, 1 perimeter and 0% infill. And they're almost perfect, very light and just as strong as previous prints with .4 using 3b 4t and 2 perimeter. The watering can is from thingiverse and printed at 60mmsec, 3 bottom and in vase mode. Also worth noting i check filament diameter periodically as i go through the roll and so far it's been between 1.72-1.77mm. Overall still my new favorite go to pla. I definitely prefer a matte finish and this filament definitely delivers.

The size is a standard roll. It works great in Bambu P1S AMS. I have not noticed any cardboard disintegrate when using it. I gotta say that the color is a nice matte. Great quality as well. Since it is PLA, there is minimal smell. It printed with good consistency throughout the projects that I made. It is also very well priced compared to other brands.

I've been using Overture PLA filament for my 3D printing projects, and it has exceeded my expectations! The filament feeds smoothly without tangling or clogging, and the prints come out with excellent layer adhesion and minimal stringing. The colors are rich and vibrant, and the finish gives prints a professional look. Whether you're a beginner or an experienced printer, Overture PLA is a reliable and high-quality choice. I highly recommend!

This filament was a little bit of a pain to print but it came out okay. Have to go slow with higher heat. The look is perfect. There's no string. I didn't have any tangling and the size is perfect I've been on a quest for the right filament to print the stones from The fifth Element and this was perfect

Wow, I’ve tried multiple different brands before landing on overture because I liked the matte black color PLA they’ve got. This rock PLA has outstanding results I personally think because it has a level of flexibility, it’s still super sturdy like all PLA but when snapping supports off things like limbs and weapons the material will bend before snapping. Not only that but the material color and complexion itself adds depth and detail I don’t find with other color PLAs. No odor whatsoever, it’s almost a softer material (the way you’d compare gold metal to iron). NO STRINGS! I’ve got about 300hrs working with this PLA and I don’t get any strings unless a support fails which is much less often then other colors!

This has a matte, stone-like finish to it. Some reviewers have complained that it is a bit difficult to work with, and it does have some quirks -no denying it. I have found that it sticks pretty well to PEI plates if you keep your plate heat at least 50F (I may go a little higher on my next print) and while the instructions recommend a nozzle temp max of 220, I've found 225F works best for me. Less than this has resulted in failure to bond, with the resulting spiderweb. So far, I like the thread and am eager to try some other prints. I'm also eager to see how well it accepts paints. I had hoped it would have more of a granite look, but the dark specs in the plastic give it more of a marble-like rock look. One of my co-workers actually thought it was stone until she picked it up (grin). Overall, I'm impressed with it. No clogs, and pretty painless (so far). Recommendations: Run a little on the hot side. This is an abrasive plastic. Make sure your bed is well leveled and the hot-end is close to the bed or it won't stick to the bed. I look forward to trying some colored versions of this thread. Note: it did not come with a print bed like some of their other spools usually do (no big deal since I rely on my PEI plate). --- Update 10/21 Still love this stuff! Just completed a candy bowl skull for Halloween. I'm going to be ordering a new roll shortly. I continue to be impressed! For statues or 'stone work', this is my new "go-to" filament.

Manufacturer included some Easter eggs inside - an attachable print surface, and little measuring/removing tool for prints. PLA looks nicely manufactured. Quality goods!

Great prints, used it on bambulab P1S with AMS, works well in AMS in its original cardboard spool, no clogging

セール時にホワイト・シルクを購入しました。 一見してわかるほど艶があるわけではないです。角度によっては安いホワイトABSに見えます。 その代わり、かどうかは分かりませんが、シルクのフィラメントにしては安定性がよく、薄くてもボロボロにはなりません。 普通のホワイトPLAと比べたら明らかにシルク感はあるので、ホワイトと組み合わせてアクセントをつけた造形はどうだろうかとアイデアを練っています。

I had high hopes for this Matte PLA, however the result is mixed.. For a relatively large base plate area, this PLA seems to have a hard time stick to the hot bed. The most interesting bit is I am using the official Overture Matte PLA setting given by Bambu Lab.... Apart from hot bed issues, it also very easy to snap... I printed so many PLA and Mattee PLA and this filament feels so easy to break... Otherwise the colour is good, seems to be well-packaged item. Comparing to other brands, this filament is relatively expensive and I was expecting it to be better, I am quite disappointed with all these issues.

Fast delivery and good quality materia gives excellent printing. Highly recommend.